How to Fix Glass Repair in Tulsa Without Going to Auto Glass Shops?

An average glass replacement takes 1.5 to 2 hours, while an average auto glass repair in Tulsa takes roughly 15 to 20 minutes to...
HomeBusiness NewsHow to Fix Glass Repair in Tulsa Without Going to Auto Glass...

How to Fix Glass Repair in Tulsa Without Going to Auto Glass Shops?

An average glass replacement takes 1.5 to 2 hours, while an average auto glass repair in Tulsa takes roughly 15 to 20 minutes to fix. It is advisable to opt for repair instead of replacement. Therefore, it is crucial to promptly address and resolve any cracks or chips present in the automobile glass. This will help maintain the car’s structure and integrity. In this article, we’ll share how anyone can repair automobile glasses at home without getting help from any auto glass shop. 

How to repair auto glass at home?

Over time, chips and cracks on auto glass caused by road debris or impacts will inevitably expand. Fortunately, it is possible to repair some minor chips and damages at home using a repair kit.

  • Buy a repair kit.
  • Take care to wipe the glass in the vicinity of any chips or cracks.
  • Attach the patch with adhesive and fix the plastic pedestal provided in the kit.
  • Use the syringe to introduce the epoxy resin into the equipment.
  • Allow the resin to cure, and clear the pedestal
  • Clean the glass thoroughly and remove any extra epoxy.

10 simple steps to repair auto glass in Tulsa:

To make it even easier to apply and simple to use, we have broken down the process of glass repair in Tulsa into 10 steps which are- 

 

  1. First, remove the paper backing from the adhesive patch to reveal one side of the adhesive. The size of the chip must not exceed the circular cutout in the middle of the patch. After that, align the patch over the chip and attach it to the clean and dry outdoor-facing side of the windshield glass. Next, peel off the paper backing’s other side and fasten the pedestal, which is a moulded plastic piece with a tube angling upward, onto the adhesive. Ensure that you line up the tabs for easy removal.
  2. Ensure that your resin is properly mixed. Then, carefully pour the liquid resin into the pedestal, filling it up completely. Next, firmly insert your syringe into the pedestal by compressing it all the way down. This will ensure a fast and effective repair for your auto glass.
  3. Hold the pedestal with one hand and slowly pull up on the syringe plunger without drawing up the resin. This creates a vacuum that removes air bubbles from the chip. Follow the instructions for how long to let the syringe sit, usually 1-10 minutes. Wait to proceed until there are no more bubbles.
  4. Hold the pedestal with one hand while removing the syringe with the other. Then, reinsert the needle and gradually push the plunger down to push the resin into the damaged area, stopping halfway as instructed.
  5. To release any trapped air bubbles in the chip, lightly tap your knuckles on the window. In case there is a spot in the chip that isn’t filled, slightly compress the syringe further down, but just a little (half an inch) to avoid damaging the adhesive seal and restarting the process.
  6. Reference the guidelines regarding the duration of the syringe’s placement in this stance. Once the epoxy resin has hardened, kindly detach the adhesive patch and pedestal.
  7. Before wiping anything, apply a small amount of resin directly onto the chipped or cracked area.
  8. To fix a chip or crack, take the curing strip and place it over the resin drops. Make sure to angle it so that air bubbles don’t get trapped. Hold the strip with your fingers and use a razor blade to remove any air bubbles. Let it cure for the recommended time.
  9. To remove the curing strip, it is recommended to avoid pulling it off directly. Instead, place your finger on top of the affected area and use a sharp razor blade to separate the strip from the glass along the perimeter. After breaking the bond, gently twist the ribbon off to avoid any damage to the resin inside the chip or crack.
  10. To eliminate any remaining resin, scrape the glass in a perpendicular direction using a razor blade. Your glass repair in Tulsa is done. 

How big is too big to consider?

Current auto glass repair standards define short cracks as less than 6 inches and between 6 to 14 inches as long cracks. In many cases, even big cracks can be repaired rather than a replacement. An average replacement cost is around $400, while the average repair price is $50, which is over 85% cheaper than replacement. Opting for crack repairs can lead to immediate savings of 60-75% and have a 100% effective outcome compared to a full replacement. Around 63% of replacements occur due to a crack that measures less than twelve inches. Repairing the existing auto glass in Tulsa helps reduce waste and minimizes the environmental impact. 

Professional Auto Glass Repair in Tulsa:

Tulsa Windshield Replacement is a top auto glass repair and replacement shop that offers the best auto glass repair in Tulsa. Our team of experts is ready to help you get your vehicle back on the road safely and quickly. To consult with our expert, call us at +1 918-610-9967.